Holiday absence
The CMT office will be closed over Easter (April 18th-21st) and on May 1st.
Holiday absence
The CMT office will be closed over Easter (April 18th-21st) and on May 1st.
CMT supplies a wide range of accessories needed for your vibration measurements.
Use the Measuring Pads for constant, faster measurements. Find your measuring points always per magnet.
Different sensors allow ever proceeding analysis.
Measure every point from one place with the Quick Connection Box.
Our range of AC 100 mV/g accelerometers is designed for use with all types of data collectors and online systems using two-wire constant current method of drive.
The range includes standard, high performance premium accelerometers, each manufactured to the highest ISO standards and backed by our outstanding technical customer support services. Options include sensitivities of standard 100 mV/g, or choose from: 10 mV/g, 30 mV/g, 50 mV/g, 250 mV/g or 500 mV/g.
The complete acceleration sensors do come with sensor, coiled cable and magnet since this is the most common combination for data collectors.
The Connection Box is used as a terminal to collect the signals from multiple channels and to supply them for external readings. There is no need to check on every measurement point. Just connect your sensors to the Quick Connection Box and you can take all measurements at the box.
Easily switch from one Sensor to the next. This high quality product is made from stainless steel and is IP 66 certified. That makes it perfect for the use on board of a vessel. The Quick Connection Box is compatible with all of CMT’s vibration devices. There are multiple output options available on request.
As a standard connection to achieve reliable results it is recomended to use a Measuring Pad on the machine with the magnet mounted to the sensor.
CMT provides two different magnets for curved and flat surfaces.
The most optimal measuring results will be achieved with the newly designed CMT Quick Fit Connection.
This requires one Quick Fit Base attached to the sensor and on each measuring point a Quick Fit Measuring Pad which is also protected with a yellow cap while it is not in use.
Permanently installed sensors should have a bolt-on connection using the measuring pad with a stud.
To achieve a comparable measuring trend it is recommended to stick to the same routine at every measurement.
To help with consistent measurements, CMT is offering Measuring Pads. The Measuring Pads are glued on the machine to guarantee that the same measuring spot is being used at every measurement.
Most important for good results is a tight and firm connection between sensor and machine. The established best practice is to use CMT Measuring Pads. The Measuring Pads are equipped with a yellow protection cap for easy recognition and protection against any dirt or paint.
CMT uses specially packed rapid curing synthetic metal glue to permanently mount measuring pads on metal surfaces. Simple hand mixing ensures activation reaction between the concentrically packed components.
All loose material, rust and surface contaminants, including existing coatings, must be removed and the surface roughened by using an angle grinder etc.
IB-CT-50055
Quick Connection Box
VIB-CT-50029
Magnet - Pole Piece
Stud for Sensor: 1/4”-28 UNF male
Diameter/Height: 25 /18 mm
Pull Strength: 20 kg
VIB-CT-50021
Magnet - Flat Face
Stud for Sensor: 1/4”-28 UNF male
Diameter/Height: 30 /10 mm
Pull Strength
VIB-CT-50048
Quit Fit Base for Sensor
Mounting Thread: quick fit
Srud for Sensor: 1/4”-28 UNF male
Diameter/Height: 24/10 mm
Wrench size: 22 mm
VIB-CT-50051
Measuring Pad for Magnet (10)
Flat surface (Including protection cap)
Diameter/Height: 24/10 mm
VIB-CT-50050
Quick Fit Measuring Pad (10)
Mounting Thread: quick fit
(Including protection cap)
Diameter/Height: 24/10 mm
Wrench size: 22 mm
VIB-CT-50011 c
Measuring Pad for Stud (10)
(Recommended for permanent installation)
Mounting Thread: M6 x 1 mm
Diameter/Height: 24/10 mm
Wrench size: 22 mm
VIB-CT-50052
Screw Studs (10)
Threads: M6 x 1 / 1/4”-28 UNF
VIB-CT-50018
Epoxy Metal Glue for Measuring Pads
Drying time: 2 hours at 20°C
Max. Temp: 120°C
Handling time:
Capacity: 20-30 Pads